When something stops working and you are not sure why, the first call is to find out what is actually going on. We handle electrical repairs, panel upgrades, wiring, lighting, EV charger installation, generator hookups, and everything in between for homes and businesses in Johnston.
Call (401) 535-9265 and we will scope the job on the phone, give you a price, and confirm the appointment before anything is scheduled.
Johnston is a city with a substantial share of older residential housing, and the electrical work that comes out of it reflects that. Knob-and-tube wiring, undersized panels, and circuits that were never designed for a modern household's load are common findings. We work through all of it, from a single outlet that stopped working to a full rewiring project. We are available every day from 7:30 AM to 11:00 PM.
Some electrical problems announce themselves clearly. A dead outlet, a panel that hums, a breaker that trips every time the dryer runs. Others take more work to find. A circuit that fails under load but resets fine when nothing is drawing on it. A fault that only shows up in damp weather, when moisture is getting into a connection somewhere. A light that flickers only at certain times of day, which points to a load condition elsewhere on the circuit rather than the fixture itself.
Finding an intermittent fault is its own job. It means working through the circuit methodically, testing under the conditions that produce the symptom, and not stopping at the first thing that looks off. A breaker that keeps tripping is a warning worth heeding, and a fault that comes and goes is not one to leave until it becomes constant.
Not every call is a diagnosis call. When the cause is clear, we move straight to the fix. When it is not, we say so on the phone and explain what the diagnostic process involves. You get straight answers about your panel and wiring before any work starts, including an honest read on whether the problem is a quick repair or something that will take time to trace.
We check the circuit from the panel out, look at the devices and connections involved, and test under load where the symptom requires it. For faults tied to moisture or weather, we look at enclosures, conduit entry points, and outdoor wiring runs. The goal is to find the actual cause rather than replace components until something holds.
Electrical work does not always happen at a convenient moment. A fault that shows up midweek in a house with tenants, a panel that needs attention before a renovation can proceed, a business that cannot close for a day while a circuit is sorted out. We work around those constraints. The appointment is set on the call, and we confirm what access looks like before we arrive.
For situations that will not keep, we take short-notice calls and work to fit them into the schedule as quickly as what is available allows. For businesses and rental properties, we can work around operating hours when the job permits it. Call and we will tell you what the schedule looks like and what can be arranged.
On a renovation or an addition, the electrical rough-in has to happen before the walls close. That means the electrician needs to be on site after framing is up but before insulation and drywall go in. If the wiring is not run at that stage, the wall has to come back open later, which adds cost and time to the whole project.
The same applies to a kitchen or bathroom remodel. New circuits for appliances, GFCI protection at the required locations, recessed lighting rough-in, and any load calculation work all need to happen before the finish trades arrive. Getting the order wrong means delays for everyone on the job.
We work with contractors and homeowners managing their own renovations. When you call to scope the project, we will tell you at what point in the build the electrical work fits, what we need access to, and what the panel needs to support the finished load. If a subpanel is part of the project because the addition is far from the main panel or the load warrants it, we cover that in the same conversation.
Every job gets treated like it matters, because it does.
Rental properties in a city like Johnston carry their own requirements around electrical work. A landlord may not be on site when the work happens, which means access has to be arranged with a tenant and the scope has to be clear before anyone shows up at the door. We work through that on the call: who is providing access, what the tenant has been told, and what time works for the property.
On the invoice side, we bill to whoever is responsible for the work. If the landlord is paying and needs documentation for their records, that is part of the conversation when the job is booked. After the work is done, you have a record of what was completed, what was found, and what the property's wiring looks like now. For rental units that have not had the wiring assessed in years, an electrical safety inspection is a practical starting point before a new tenancy begins.
An outdoor outlet that is not in a weatherproof enclosure is a code issue and a practical one. Water in a receptacle box causes faults that are hard to trace and can damage whatever is plugged into it. We install weatherproof outlets and covers for exterior locations, with GFCI protection where it is required, and we run new circuits to reach locations that were never wired for outdoor use.
Battery-powered alarms are a starting point, but hardwired alarms with battery backup are what current standards call for in most residential installations. They are interconnected, so when one sounds, they all sound. We install and replace hardwired smoke and CO alarm systems, including the wiring runs between units and the connection back to the panel.
This one is covered in more detail above, but it belongs here too because it is a distinct type of call. Intermittent faults do not always produce a clear symptom on demand. We test under the conditions that cause the problem, work through the circuit systematically, and do not close the job until the fault is found and corrected.
A welder or an air compressor draws a sustained load that a standard household circuit is not designed to carry. Running a dedicated circuit for workshop equipment means sizing the wire and breaker correctly for the equipment's rated draw, not just its startup current. We run load calculations before pulling wire, confirm the panel has capacity, and install the circuit to the outlet or connection point the equipment requires. If the panel is already at its limit, that conversation happens before the work starts.
The price for any job is confirmed on the phone, based on what you describe. For a straightforward repair or installation, that conversation is usually enough to give you a clear number. For a more complex job, the on-site assessment fills in what the phone call cannot see: what the wiring behind the wall looks like, whether the existing panel has room for the added load, and whether the circuit can carry the change without an upgrade.
The things that move a quote are the things that change the scope. What the fault turns out to be once it is traced. What has to be opened up to reach it. Whether the panel needs attention alongside the original job. We explain any of those on-site before we proceed, so the price is agreed before work continues. Simple scheduling. Pricing agreed up front. Power back fast.
To get a quote, call (401) 535-9265.
We go through the job on the phone, ask the right questions, and give you the rate before anything is booked.
We serve Johnston and take calls from across the surrounding communities in Providence County. If you are in a neighboring city or town, call and we will confirm your address is covered.
Communities we serve regularly include:
If you are elsewhere in Providence County, call and we will tell you whether your address falls within our range. Real experience. Local knowledge. Ready to wire. For the full list, go to our page listing every electrical service.
Call us with the dates and the scope of what needs to be done. We assess whether the work can be completed in the available window and schedule accordingly. Being specific about the timeline on the call helps us confirm whether it is realistic.
Yes. We work through the access arrangement on the call before the visit is scheduled. That means confirming what the tenant has been told, what time works for the property, and what the scope of the work involves so there are no open questions when we arrive. Landlords who need documentation after the work is done can request that when the job is booked.
Older homes in this area frequently have knob-and-tube wiring, aluminum branch wiring, or panels that were sized for a much lighter load than a modern household places on them. GFCI and AFCI protection is often missing at locations where current code requires it. An electrical safety inspection is the clearest way to find out what the wiring looks like and what, if anything, needs to be addressed.
Framing needs to be complete and the layout of outlets, switches, and fixtures needs to be confirmed before rough-in begins. Any changes to the plan after the rough-in is done mean reopening walls. We work through the layout with the builder on the call to confirm what needs to be decided before we arrive.
Yes. We serve Johnston and the surrounding communities in Providence County, including Greenville, Smithfield, North Providence, and Providence.
Call (401) 535-9265 and we will confirm your address is within our service area.
We explain what each finding involves and which ones represent immediate concerns versus items that can be addressed on a planned schedule. The call after an inspection is the right time to work through that conversation and decide what gets done first.
Whatever brought you to this page, whether it is a fault you cannot pin down, a panel that needs attention, or a project that needs the electrical side planned before the rest of the work starts, we handle it.
Call (401) 535-9265 and we will talk through the job, give you a price, and get it scheduled. We are available every day from 7:30 AM to 11:00 PM.
We are also in: North Providence, Smithfield, Providence, Scituate. Have a look at our full coverage area.
Below is a plain-language breakdown of the electrical work we handle in Johnston and across Providence County. Each row covers what the service includes, who it fits best, and one practical detail worth knowing before you call. If your situation does not fit neatly into one row, call and we will talk through it.
| Type of Work | Scope of Work | When You Need It | Things to Know |
|---|---|---|---|
| Breaker & Fuse Repair |
| Homes with a breaker that trips repeatedly or a fuse box still in service | A breaker that keeps tripping is a warning worth investigating, not just resetting. |
| Wiring & Circuit Installation |
| Renovations, additions, and homes where wiring has been flagged during an inspection | Whole-home rewiring is a multi-day project. Partial rewires are scoped to what the home actually needs. |
| Electrical Panel UpgradesMost Popular |
| Older Johnston homes adding appliances, EV chargers, or additions | Many pre-1960s homes in this area are still on 60-amp or 100-amp service, which falls short of modern demand. |
Call (401) 535-9265 to talk through your electrical situation and get a price before anything is scheduled.
(401) 535-9265